Sailboat Keel Types: A Complete Guide
Last Updated by
Daniel Wade
June 15, 2022
A keel is a very important part of a sailboat, crucial to its stability and ability to sail upwind. This article will discuss the fundamentals of all keels down to the details of the best keel for your boat. We will answer questions including what it does, what it's made of, and even some problems that a keel can cause. By the end of this article, you will be an expert on all things keels!
Table of contents
What Is a Keel?
A keel is the robust underwater centerline of a boat, and often extends into a long, hydrodynamically shaped blade.. It can vary in size and shape depending on the make and model of the boat. But, generally, it will look very much like a fin. If you imagine the fin on the underside of a surfboard you will have a pretty good idea of what it looks like under the boat.
It is crucial to helping with steering and control. The word keel itself comes from Norse and Dutch roots. The word simply means a structural component of the boat. You may have heard the term keel-haul, where pirates would drag someone underneath the boat across its keel. This is pretty barbaric, but it shows just how long a keel has been an important part of the boat. From Vikings to pirates to modern sailboats it has always remained an important part of a sailboat.
What is a keel made of?
A keel will typically be made of whatever the rest of the hull is made of. If the boat is wooden, it will most likely have a wooden keel. If the boat is metal, the keel will be metal, and so on. Sometimes, particularly on fiberglass boats, the core of a keel will be reinforced with lead or a similar ballast while the outside is covered with fiberglass.
The keel needs to be strong enough to withstand a lot of pressure and strain. Traditionally Viking sailing boats would have a wooden keel with some metal plating on it. Casting metal was tedious so putting it on your boat was seen as a waste. Traditional wooden sailing boats, like you would imagine pirates sailing, would also have a wooden keel. It would be made from thick hardwood like oak and could also be metal plated.
Since it is used to control the direction it must brunt the force of the change of direction. If you imagine a boat turning sharply, there will be a lot of pressure on the side that is on the outside of the turn. The hull of your boat will stand up to this pressure easily, as it is very large and very strong. The keel must be strong enough to withstand this too. The keel also can drag on the ocean floor or the boat ramp as the boat is lowered into the water. For this reason, it needs to be strong enough to hold up to the weight and pressure of the boat too. If it were made of plastic it would break every time you brought the boat in and out of the water.
What does a keel do?
The keel is there primarily for stability and guidance. The keel provides all sorts of benefits to the boat. It improves the righting moment and controls the boat’s sideways movement. The keel will also typically hold the boat’s ballast. The ballast keeps the boat weighed down and helps prevent capsizing. The ballast is typically made of lead, sand, or water.
Keels can be fixed or moveable. Some keels can be removed completely or may just retract slightly so they aren’t damaged when the boat enters or exits the water. When a boat leans to one side, because it is turning or there is strong wind/waves, the keel provides the righting moment that keeps the boat from flipping. On larger boats, it is designed to be so heavy that ig will be able to recover a boat from almost any angle of heel. Without a keel, your boat may tip too far or roll completely. On bigger ships, this can be disastrous. In its ability to prevent this alone, the keel is one of the most important parts of the ship.
Does my sailboat need a keel?
Yes, you do need a keel. Pretty much all sailboats have a keel, with exceptions for multi-hulled and/or smaller boats.
In the case of catamarans, the very design principles that lead to the dual-hull design render the keel obsolete. The stability introduced by the outrigged, dual-hulls replaces the necessary righting moment from the keel. Because almost all the structure of a catamaran is between the two hulls, unlike a monohull which builds out from and around its centerline, there is not a lot of weight pressing out to flip the boat. Related to this, since most catamarans have the length of their hulls pressing into the water, the steering force normally placed on a keel is distributed across the length of the two hulls, which additionally will carry their own ballast.
On smaller dinghies, a small swinging centerboard or daggerboard will suffice to play the role of a keel. The centerboards can be big enough to keep the boat flowing nicely through the water without the need for a large keel. Additionally, it is not a disaster for a small sailing or racing dinghy to capsize, as they are designed to do so and recover rather easily, so the ballast from the keel is also not terribly necessary.
If you have a motorboat you wouldn’t need a keel, unless it is a very large container ship or military vessel. The reason being that they are outboard propelled. The leg provides enough stability on its own. This is only the case with full plane powerboats. Displacement (even semi-displacement) craft will still need a keel of sorts for stability purposes.
What are some downsides to having a longer keel?
If you have a long keel that doesn’t retract or detach, you may have some problems coming in or out of the water. The keel extends far below the bottom of the boat, so if you are bringing your boat up or down a boat ramp you may find that it scrapes on the bottom. If you are not careful, you may damage the keel rather badly.
Since the keel is made of metal, wood, or fiberglass it can bear the brunt of the weight quite well. If you are putting your boat in the water and cannot retract the keel, it is a good idea to go as far into the water as possible before taking your boat off its trailer. The deeper you are in the water when the boat is released the better.
Are there any nautical traditions about the keel of the boat?
The keel is interestingly very important when it comes to boat or shipbuilding.
Traditionally, the keel is one of the first parts of the ship to be made, as the rest of the ship must sometimes be built around it. This tradition is called “laying the keel,” and is a momentous occasion. It is essentially the boat’s birthday. The boat’s age is dated from this moment, and there is also typically a celebration of sorts. This goes back to the days of seafaring exploration. The only day more important in a boat’s life is the day it is finally launched.
Can other types of boats have keels?
Yes! Many other types of boats have keels, not just sailboats. A good example would be a big shipping trawler. These trawlers are very large and need all the help they can get to stay balanced. Because of this, they often have what’s called a bar keel. This is a large rectangular piece of metal that runs along the bottom of the boat’s hull. It is very thick and heavy. The idea is that it gives the boat some more directional control when steering.
Furthermore, it helps keep the trawler balanced when out at sea in rough conditions. The extra weight keeps the boat’s center of gravity as low as possible. This makes tipping the boat almost impossible. It does slow it down a bit, but that is a small price to pay for increased safety.
Huge cargo ships also have a keel, though it is different from a bar. Their keel is known as a plate keel. It is essentially another layer of the boat under the hull. Its only purpose is added weight and protection. A plate keel runs along the centreline of the bottom plate of the ship so the weight is all concentrated in the lowest place possible. This kind of keel works similarly to how the spine of a person does. It keeps your back strong and as straight as possible.
How important is it to keep my keel clean?
It is very important to keep your keel clean, just as it is important to keep the rest of your hull clean.
For any boat kept on the water rather than hauled out every day, there is always the need to clean the hulls and keels of any barnacles and other sea growth. Barnacles not only affect your performance, but can, in the long run, greatly increase your maintenance costs if not regularly addressed.
To do so, you have to do what is known as scraping. Scraping is the process of physically scraping off all the barnacles and other sea life that has attached itself to the underside of your boat. Many marinas offer this service, but you can do it on your own with a basic plastic paint scraper and a wetsuit. When you do this, it is key to get all the way down to the bottom of the keel and all across the hull. If you don’t scrape it off, it can start to erode your boat away over time. It can also slow you down.The barnacles and other marine life create a very rough bottom. This creates more friction and will reduce your speed more and more the worse it gets.
It is important to check with your port authority before you start scraping. Scraping is not allowed in some places as you may introduce invasive species to the area. It depends where you have been more than where you are. If you sailed from New York to Chicago, you will be fine. If you sailed from Cuba to New York, probably not so much.
How to maintain a sailboat keel
As mentioned above, it is important to scrape your keel from time to time. While racing boats will actually do this before every day at an event, it is at least a good idea for you to do this a couple of times a season. A great time to do this is when you plan on applying that season’s bottom paint, though anytime you plan to go on your boat is a good excuse to maintain!
You may want to cut off any of the kelp and seaweed that wraps itself around the keel. This is more likely to happen if you have a fin keel. If you do find that there is a lot of kelp and seaweed wrapped around it, you will want to buy yourself a kelp cutter. Unfortunately, the only way to cut the kelp off without taking the boat out of the water is to dive in and do it yourself. It is a good idea to do this in shallow-ish water with the proper flags displayed to inform other boaters that there is someone in the water. Swimming around under your boat, even when it isn’t moving, can be dangerous.
What do I do if my keel breaks at sea?
It is very rare for keels to just break off. It is even rarer at sea. After all, what is going to break it off? The only way a keel will break off ordinarily is if you run aground.
If you should accidentally make your way into shallow waters and break your keel off it is a good idea to set sail for home. You will manage well enough in the short term but will struggle over time. You are far more likely to capsize without the keel keeping you balanced.
If you have a detachable keel it is a good idea to keep a replacement. If one breaks off, you can just install the spare one. This isn’t the easiest thing to do at sea in rough conditions, but it is possible. Make a judgment call using your common sense whether it is worth the risk or not.
Another reason your keel might break or come loose is if the keel bolts come out. These bolts are what holds the keel in place. If you happen to have a keel held on by bolts, then doing proper maintenance is even more important. If the bolts come loose, the keel can come loose.
Since the keel is typically welded on to the boat’s hull the chances of it coming off completely are slim to none. Most often, running aground on a sandbar or anything short of an incredibly rocky bottom in heavy weather will crack off a piece or severely bend the keel, which requires a major repair. If you do notice that the keel is loose, you are better off taking it back to the marina. The bolts may not come off without using some machinery, meaning you might have to take your boat out of the water. If your keel starts to rust, you may need to speak to a professional.
What are the different keel types?
Now you know what a keel is, what it does, why it is important, and how to care for one it is time to learn about the specific types of keels. Big trawlers and cargo ships have bar or plate keels, but sailboats do not. Here are the 6 different types of keels typically found on sailboats and their purposes:
The full keel is one of the most common types of the keel that you are likely to see on a sailboat. A full keel runs from end to end of the boat lengthways. A full keel, as the name implies, runs almost the entire length of the boat. At a minimum, it must run 50% of the length of the boat. A full keel is one of the most stable keel types, which is why it is so common. Full keels are also safer should you run aground. If a boat with a full keel should come ashore, it will cut its way through the sand and eventually land on its side. Whether you are grounding your boat intentionally or not, your boat will have far better odds of surviving the ordeal with a full keel.
A fin keel is similar to a full keel, just shorter. There may be one or two fin keels along the length of the boat hull. A fin keel is defined by being less than 50% the length of the boat. The fin keel works almost entirely the same way that a shark's fin does. When you wish to turn, the keel provides the resistive force that keeps you turning. This means that it essentially acts as your tires going into a turn. Whereas a full keel is essentially just a long fin, a fin keel has very different benefits. A full keel is more stable and safer overall. A fin keel is sleeker, smaller, and most importantly makes you faster. Most racing sailboats have fin keels.
A bulbed keel is very similar to a fin keel. In fact, it is possible to make a bulb keel by shaving off part of a fin keel and attaching a bulb. Once the keel has been made substantially shorter, the bulb is fitted. The bulb is shaped similarly to how a torpedo would be on a submarine. This keel works the same as a fin keel does, offering a slightly more stability without sacrificing speed. The biggest difference between a bulb and a fin keel (besides shape and length) is where they are used. Bulb keels are most commonly used in places with very shallow waters and lots of rock/shale/coral outcrops. Somewhere like the Caribbean would be the perfect place for a bulb keel. The rounded bulb bounces off the rocks and is less likely to break off. It just isn’t going to be as quick as if you used a fin keel.
The wing keel is another alternative to your standard fin keel. Just like the bulb keel, a wing keel is an extension to the standard fin keel with an extra fitting at the bottom. A wing keel is far more streamlined than a bulbed one, at the expense of being more susceptible to breaking. A wing keel looks very similar to the tail of an airplane. It works the same way, too. The water can pass by either side of the wings, allowing you to adjust your course easily. But, a wing keel does have one major problem. If you do run aground, digging out a wing keel can be very difficult. Whereas digging out a standard fin is as simple as scraping sand away from the sides of it, a wing keel must be dug out completely. The wings act like little shovels and wedge themselves into the sand. These are generally limited to higher performance racing classes.
Centerboard Keel
A centerboard keel works similarly to a fin keel but it can retract slightly. It works by having a dagger that folds out downwards. When you are sailing, the dagger protrudes outwards and offers you all the stability and balance of a fin keel. When you are in shallow water, the dagger can be retracted upwards, essentially shortening the keel temporarily. This should be done when you are sailing in shallow waters or removing the boat from the water entirely using a boat ramp. Some centerboards work on a loose hinge. When the boat is sailing along, the dagger is out and the fin works as normal. If you should bump into something though, like some shallow rocks, the hinge would push the daggerboard back inside. This stops the keel from breaking, instead, it just moves out the way. This only works if you are only just deep enough. If you are in very shallow water you would just break the centerboard off.
Canting Keel
A canting keel also works on a hinge. Instead of working end to end, it works port to starboard. When the boat turns a corner, the canting keel swings from side to side. This allows the boat to maximize its balance and speed. Eventually, this will become the norm in racing. But at the moment it is still quite experimental. The biggest downside is that the hinge works on hydraulics, and hydraulics can fail. If they should fail at sea there is very little you can do to repair them. Once they have perfected these canting keels, they will move first into the racing classes and high performance boats, then to all new cruising boats as boatbuilders improve the technology. .
Hopefully, you now have a good idea about what a sailboat keel is,how it works, why it is so important, and, of course, all the different types. Chances are, when you buy a sailboat , the keel it has is going to be at the bottom of your list of priorities. That being said, if you are planning on sailing somewhere in particular, it is a good idea to think about what keel type you are using. Replacing them doesn’t have to be expensive, but you can go a long way to saving yourself that money either way by being prepared for your home waters!
Related Articles
I've personally had thousands of questions about sailing and sailboats over the years. As I learn and experience sailing, and the community, I share the answers that work and make sense to me, here on Life of Sailing.
by this author
Learn About Sailboats
Most Recent
What Does "Sailing By The Lee" Mean?
October 3, 2023
The Best Sailing Schools And Programs: Reviews & Ratings
September 26, 2023
Important Legal Info
Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies.
Similar Posts
Affordable Sailboats You Can Build at Home
September 13, 2023
Best Small Sailboat Ornaments
September 12, 2023
Discover the Magic of Hydrofoil Sailboats
December 11, 2023
Popular Posts
Best Liveaboard Catamaran Sailboats
December 28, 2023
Can a Novice Sail Around the World?
Elizabeth O'Malley
4 Best Electric Outboard Motors
How Long Did It Take The Vikings To Sail To England?
10 Best Sailboat Brands (And Why)
December 20, 2023
7 Best Places To Liveaboard A Sailboat
Get the best sailing content.
Top Rated Posts
Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies. (866) 342-SAIL
© 2024 Life of Sailing Email: [email protected] Address: 11816 Inwood Rd #3024 Dallas, TX 75244 Disclaimer Privacy Policy
- AI Generator
Premium Access
Custom content, media manager.
Grow your brand authentically by sharing brand content with the internet’s creators.
296 Sailboat Keel Stock Photos and High-res Pictures
Browse 296 sailboat keel photos and images available, or start a new search to explore more photos and images..
- AI Generator
Premium Access
Custom content, media manager.
Grow your brand authentically by sharing brand content with the internet’s creators.
296 Sailboat Keel Stock Photos and High-res Pictures
Browse 296 sailboat keel photos and images available, or start a new search to explore more photos and images..
- AI Generator
Premium Access
Custom content, media manager.
Grow your brand authentically by sharing brand content with the internet’s creators.
sailboat keel
4,594 keel stock photos & high-res pictures, browse 4,594 authentic keel stock photos, high-res images, and pictures, or explore additional boat keel or keel beach stock images to find the right photo at the right size and resolution for your project..
- Images home
- Editorial home
- Editorial video
- Premium collections
- Entertainment
- Premium images
- AI generated images
- Curated collections
- Animals/Wildlife
- Backgrounds/Textures
- Beauty/Fashion
- Buildings/Landmarks
- Business/Finance
- Celebrities
- Food and Drink
- Healthcare/Medical
- Illustrations/Clip-Art
- Miscellaneous
- Parks/Outdoor
- Signs/Symbols
- Sports/Recreation
- Transportation
- All categories
- Shutterstock Select
- Shutterstock Elements
- Health Care
Browse Content
- Sound effects
PremiumBeat
- PixelSquid 3D objects
- Templates Home
- Instagram all
- Highlight covers
- Facebook all
- Carousel ads
- Cover photos
- Event covers
- Youtube all
- Channel Art
- Etsy big banner
- Etsy mini banner
- Etsy shop icon
- Pinterest all
- Pinterest pins
- Twitter All
- Twitter Banner
- Infographics
- Zoom backgrounds
- Announcements
- Certificates
- Gift Certificates
- Real Estate Flyer
- Travel Brochures
- Anniversary
- Baby Shower
- Mother's Day
- Thanksgiving
- All Invitations
- Party invitations
- Wedding invitations
- Book Covers
- About Creative Flow
- Start a design
AI image generator
- Photo editor
- Background remover
- Collage maker
- Resize image
- Color palettes
Color palette generator
- Image converter
- Creative AI
- Design tips
- Custom plans
- Request quote
- Shutterstock Studios
0 Credits Available
You currently have 0 credits
See all plans
Image plans
With access to 400M+ photos, vectors, illustrations, and more. Includes AI generated images!
Video plans
A library of 28 million high quality video clips. Choose between packs and subscription.
Music plans
Download tracks one at a time, or get a subscription with unlimited downloads.
Editorial plans
Instant access to over 50 million images and videos for news, sports, and entertainment.
Includes templates, design tools, AI-powered recommendations, and much more.
Search by image
Boat Keel royalty-free images
6,943 boat keel stock photos, vectors, and illustrations are available royalty-free for download., sailing and motor yachts.
maintenance boat with high pressure water
Sailing boat / vintage illustration from Meyers Konversations-Lexikon 1897
Boat Hull repairs/ a large wooden boat's hull getting sanded in preparation for anti foul paint being applied
Split shot of anchored sail boat with heavy clouds in sky
Cocos Keeling atoll
Sailing boat with spinnaker on windward mark - red buoy. Waterline view.
boat in dry dock, waiting for sailing season, shot with wide angle lenses
Prow of boat in golden reflections on water
Ship building of new boards
Sailboat Ship Icon. Design Element 41k, it’s specially designed with a web designers in mind to achieve PIN SHARP ICON ON A SCREEN.
Building a boat. Under construction. Toned photo. The wooden keel beams. Orange wood. Colorful image. Traditional methods. Turkey.
Blue sailing boat on the sea with keel under water
cargo ship propeller
The keel of a boat turned upside down.
Underwater view with rudder and keel of sailing boat
Vector illustration background of cartoon sailing regatta with many yachts on horizon in blue tone.
Row boat bow front end. Teal coloured clinker built rowing boat dockside ashore raised on blocks dry dock. Mount Batten Slipway, Plymouth. Beautiful teal and blue clinker built row boat.
Sloop Wooden Sail Boat
Dinghy with sail in flat style on a white background. Sailing boat illustration.
A luxury private motor yacht under way on tropical sea with bow wave
A wooden toy yacht. The toy boat shows signs of use, but the sails are in tact and still attached to the wooden mast. It is painted in 4 colours with a simple keel indicating this toy is ornamental.
Set of silhouettes of sea yachts and the ships
typical vacation hire cruiser moored on the tree lined banks of the river wensum in the city of norwich, norfolk broads with the historic bishop bridge in the background
MARSEILLE, FRANCE - APRIL 20, 2018: Slanted yacht during regatta race, Marseille, Bouche du Rhone, France
a rowing boat with anchor chain
Wave the boat
sail with keel, vector icon
Wooden Yawl yacht sailing on a sunny day in Riga bay. Two masts and a beautiful cloudscape.
ark symbol. ship logo vector.
Yacht Service in the Yacht Marine
Sailing boat (Yawl - Ketch - Schooner - Sloop) / vintage illustration from Meyers Konversations-Lexikon 1897
White yacht bow
Fishing boat on beach at low tide
Viking ship bow keel with wood carving ornaments near the waterline
Boat on the surface of the White Sea sunny summer evening
set of different ships
A boat is out on dry land for maintenance
launching a ship in shipyard
Harbour tug boat vector design
Wooden ship toy model, isolated on white background
Simple vector set of ships with sails and waves elements in blue box.
Prow of a sailboat in dry dock against a bright blue sky.
Set of different sailing ships icon (simple vector).
Barnacles on the keel of a boat
Vector illustration of four small ships in different colors: a sailboat, a yacht, a fishing boat and a rescue boat. Cartoon style.
lonely sailing ship in a storm
Illustration of the steamer and goldfish
Vector illustration of a modern competition sailboat isolated on white background. Color and line stroke editable
Heavily fouled hull
Silhouettes of offshore ships - yacht, fishing boat, the warship.
abstract textured image of a beached fishing trawler to give a well worn vintage look
traditional sailing vessel near Laboe, Kiel
Ideal beauty young laughing couple on sailing yacht. Split with underwater, real shoot.
Underwater shot of two free divers ascending from a depth along the chain attached to the boat
an abandoned wooden fishing boat on a shingle beach illuminated at night by the beam from a lighthouse in black and white
Two free divers training in the open sea along the anchor chain of the vessel
Mollusk rock borers (stone borers). The sailing ship with holey board.
Pattern of the sailings ships
wooden boat made of boards on tropical island shore with shell & surf waves, vacation dreams, vector illustration with black contour lines isolated on white background in a hand drawn & doodle style
Isometric inflatable boat. A modern inflatable boat with rigid wooden floorboards, a transom and an inflatable keel, powered by an electric trolling motor.
Recreational motor yacht isolated on white close up
Traditional Arabian Wooden Fishing Boat
Old small ski keel isolated on white sky background. Jib shallop picture. Freehand line black ink hand drawn logo sketchy in art retro doodle cartoon style pen on paper. Side view with space for text
The Illustration shows old woooden pirate's boat. Wooden ship have one mast and three cannons on the board. The illustration done in cartoon style.
Hang Yacht for renovation in the marina
Outboard motor system isolated on white close up
Vector grungy textured blue watercolor sailboat icon
Black and white: old wooden fishing boat landing on the beach
boat in watercolor ship for trip
The old wooden boat waiting for repair.
power boat parking water protected by a plastic film for wintering on sailboat stored for season cold winter
Seascape with shipwreck and rocks - vector illustration.
A sailboat runs aground and sinks in the shallow waters around Key West
small sailboat on san francisco bay
Sailing boat with red buoy from the waterline view
hiking out on a small sailboat
Old small jib ski keel shallop vehicle isolated on white sky background. Dark black ink hand drawn journey tour logo sign sketch in art retro engraving graphic style. Side view with space for text
Underwater part of tourist ship close to tropical coral reef
Vector illustration of cartoon sailing yacht in sunset (stained glass windows).
A large luxury private motor yacht under way sailing on tropical sea with bow wave
Arabian traditional boat
Hand Drawn Engraving Pen and Ink Sail Boat Vintage Vector Illustration
beautiful; colorful boats on the sea wave (vector illustration);
Lower part of stern and propeller of a fishing boat in a shipyard for maintenance.
Boat hull, skeleton of a wooden boat, wooden structure composed by Keel and frames of a half-built boat
Split shot of the sail boat anchored near the green island at sunny day
Our company
Press/Media
Investor relations
Shutterstock Blog
Popular searches
Stock Photos and Videos
Stock photos
Stock videos
Stock vectors
Editorial images
Featured photo collections
Sell your content
Affiliate/Reseller
International reseller
Live assignments
Rights and clearance
Website Terms of Use
Terms of Service
Privacy policy
Modern Slavery Statement
Cookie Preferences
Shutterstock.AI
AI style types
Shutterstock mobile app
Android app
© 2003-2024 Shutterstock, Inc.
A Guide to the Different Parts of a Sailboat
Table of Contents
When you use Boatsetter, you have the opportunity to choose from a myriad of different sailboat rentals from all over the United States and beyond . A sailboat is a perfect way to relax on the water, either on a solo adventure or on an excursion with friends and family.
When you rent a sailboat with Boatsetter, you will have the option to book a captained sailboat to enjoy your day out on the water or book bareboat to hone your sailing skills. Either way, you may be interested in the intricacies of a sailboat and its different parts. If this sounds like you, you have come to the right place. In this article, we go in-depth about the different parts of a sailboat so that you can be more knowledgeable about whatever boat you may choose and come away from reading this feeling more confident about the whole sailing experience.
A basic sailboat is composed of at least 12 parts: the hull , the keel , the rudder , the mast, the mainsail, the boom, the kicking strap (boom vang), the topping lift, the jib, the spinnaker, the genoa, the backstay, and the forestay. Read all the way through for the definition of each sailboat part and to know how they work.
Explore sailboats for rent near you or wherever you want to go
In short, the hull is the watertight body of the ship or boat. There are different types of hulls that a sailboat may have, and these different hulls will often affect the speed and stability of the boat.
Displacement Hulls
Most sailboats have displacement hulls , like round bottom hulls, which move through the water by pushing water aside and are designed to cut through the water with very little propulsion. The reason these are called displacement hulls is that if you lower the boat into the water, some of the water moves out of the way to adjust for the boat, and if you could weigh the displayed water, you would find that it equals the weight of the boat, and that weight is the boat’s displacement. One thing to know about displacement hulls is that boats with these hulls are usually limited to slower speeds.
Planing Hull
Another type of hull is a planing hull. These hulls are designed to rise and glide on top of the water when enough power is supplied. When there is not enough power behind the boat, these boats often act as displacement hulls, such as when a boat is at rest. However, they climb to the surface of the water as they begin to move faster. Unlike the round bottom displacement hulls, these planing hulls will often have flat or v-shaped bottoms. These are very common with motor-driven water vessels, such as pontoon boats, but they can also be found on smaller sailboats which allow them to glide quickly over the water.
Finally, sailboats can differ depending on the number of hulls that they have. There are three options: monohulls (one hull), catamarans (two hulls), and trimarans (three hulls).
Monohulls , which have only a single hull, will usually be the typical round bottom displacement hull or occasionally the flat bottomed or v-shaped planning hull. Catamarans have two hulls with a deck or a trampoline in between, with the extra hulls providing increased stability. Finally, trimarans have three hulls — a main hull in the middle and two side hulls used for stability. These trimarans have gained popularity because of their excellent stability and ability to go at high speeds.
When evaluating a sailboat , it is important to pay attention to the type of hull that the boat has because the type of hull a sailboat has can drastically change the sailing experience, especially when it comes to stability and speed.
All sailboats have a keel, a flat blade sticking down into the water from the sailboat’s hull bottom. It has several functions: it provides counterbalance, life, controls sideways movement, holds the boat’s ballast , and helps prevent the boat from capsizing. When a boat leans from one side to the other, the keel and its ballast counteract the movement and prevent the boat from completely tipping over.
As with hulls, there are a number of different types of keels, though the two most common types of keels on recreational sailboats are the full keel or the fin keel. A full keel is larger than a fin keel and is much more stable. The full keel is generally half or more of the length of the sailboat. However, it is much slower than the fin keel. A fin keel, which is smaller than the full keel, offers less water resistance and therefore affords higher speeds.
A more recent feature on sailboats is the “winged keel,” which is short and shallow but carries a lot of weight in two “wings” that run sideways from the keel’s main part. Another more recent invention in sailing is the concept of the canting keels, which are designed to move the weight at the bottom of the sailboat to the upwind side. This invention allows the boat to carry more sails.
The Rudder
A rudder is the primary control surface used to steer a sailboat. A rudder is a vertical blade that is either attached to the flat surface of the boat’s stern (the back of the boat) or under the boat. The rudder works by deflecting water flow. When the person steering the boat turns the rudder, the water strikes it with increased force on one side and decreased force on the other, turning the boat in the direction of lower pressure.
On most smaller sailboats, the helmsman — the person steering the boat — uses a “ tiller ” to turn the rudder. The “tiller” is a stick made of wood or some type of metal attached to the top of the rudder. However, larger boats will generally use a wheel to steer the rudder since it provides greater leverage for turning the rudder, necessary for larger boats’ weight and water resistance.
The mast of a sailboat is a tall vertical pole that supports the sails. Larger ships often have multiple masts. The different types of masts are as follows:
(1) The Foremast — This is the first mast near the bow (front) of the boat, and it is the mast that is before the mainmast.
(2) The Mainmast — This is the tallest mast, usually located near the ship’s center.
(3) The Mizzen mast — This is the third mast closest to the stern (back), immediately in the back of the mainmast. It is always shorter than the mainmast and is typically shorter than the foremast.
The Main Sail
The mainsail is the principal sail on a sailboat, and it is set on the backside of the mainmast. It is the main source that propels the boat windward.
A boom is a spar (a pole made of wood or some other type of lightweight metal) along the bottom of a fore-and-aft rigged sail, which greatly improves the control of the angle and the shape of the sail, making it an indispensable tool for the navigation of the boat by controlling the sailes. The boom’s primary action is to keep the foot (bottom) of the sail flatter when the sail angle is away from the centerline of the sailboat.
The Kicking Strap (Boom Vang)
The boom vang is the line or piston system on a sailboat used to exert a downward force on the boom, enabling one to control the sail’s shape. The vang typically runs from the base of the mast to a point about a third of the way out the boom. It holds the boom down, enabling it to flatten the mainsail.
The Topping Lift
The topping lift is a line that is a part of the rigging on a sailboat, which applies an upward force on a spar (a pole) or a boom. Topping lifts are also used to hold a boom up when it’s sail is lowered. This line runs from the free end of the boom forward to the top of the mast. The line may run over a block at the top of the mast and down the deck to allow it to be adjusted.
A jib is a triangular staysail set ahead of the foremost mast of a sailboat. Its tack is fixed to the bowsprit, the bow, or the deck between the bowsprit and the foremost mast. Jibs and spinnakers are the two main types of headsails on modern boats.
The Spinnaker
A spinnaker is a type of sail designed specifically for sailing off the wind from a reaching downwind course. The spinnaker fills up with wind and balloons out in front of the sailboat when it is deployed. This maneuver is called “flying.” The spinnaker is constructed of very lightweight material, such a nylon fabric and on many sailing vessels, it is very brightly colored.
Another name for the spinnaker is the “chute” because it often resembles a parachute, both in the material it is constructed from and its appearance when it is full of wind.
People often use the term genoa and jib as if they were the same thing, but there is a marked difference between these two types of sails. A job is no larger than a foretriangle, the triangular area formed by the mast, the deck or bowsprit, and the forestay. On the other hand, a genoa is larger than the jib, with part of the sail going past the mast and overlapping the mainsail. These two sails, however, serve very similar purposes.
The Backstay
The backstay is a standing rigging that runs from the mast to the transom (the vertical section at the back of the boat), counteracting the forestay and the jib. The backstay is an important sail trip, control and directly affects the mainsail’s shape and the headsail.
There are two general categories of backstays:
1) A permanent backstay is attached to the top of the mast and may or may not be readily adjustable.
2) A running backstay is attached about two-thirds up the mast and sometimes at multiple locations along the mast. Most modern sailboats will have a permanent backstay, and some will have permanent backstays combined with a running backstay.
The Forestay
A forestay is a piece of standing rigging that keeps the mast from falling backward. It is attached at the very top of the mast, or at certain points near the top of the mast, with the other end of the forestay being attached to the bow (the front of the boat). Often a sail, such as a jib or a genoa, is attached to the forestay.
A forestay might be made from stainless steel wire, stainless steel rod or carbon rod, or galvanized wire or natural fibers.
Parts of a sail
Sails are vital for sailboats, made up of complex parts that improve performance and maneuverability. In this section, we’ll take a closer look at the different parts of that make up the sails.
Luff – The luff is a vertical sail part that maintains its shape and generates lift by interacting with the wind. It attaches securely with a bolt rope or luff tape for easy hoisting.
Leech – The leech controls air flow and reduces turbulence. Battens or leech lines are used to maintain shape and prevent fluttering.
Foot – The foot of a sail connects the luff and leech at the bottom edge. It helps define the sail’s shape and area. The outhaul is used to adjust its tension and shape.
Head – The sail’s head is where the luff and leech meet. It has a reinforced section for attaching the halyard to raise the sail.
Battens -The b attens are placed horizontally in sail pockets to maintain shape and optimize performance in varying wind conditions. They provide structural support from luff to leech.
Telltales – Sailors use telltales to adjust sail trim and ensure optimal performance.
Clew – The clew is important for shaping the sail and connecting the sheet, which regulates the angle and tension, producing energy. It’s located at the lower back corner of the sail.
Sailing is a favorite pastime for millions of Americans across the country. For some, there is nothing better than gliding across the water propelled by nothing more than the natural force of the wind alone. For both experienced and non-experienced sailors alike, Boatsetter is the perfect place to get your ideal sailboat rental from the mouthwatering Florida keys to the crystal blue waters of the Caribbean .
Smaller sailing boats are perfect for a single day out on the water, either by yourself or with friends and family. In comparison, larger sailing boats and sailing yachts can allow you days of luxury on longer excursions full of adventure and luxury.
Whatever your sailing dreams are, it is always good to know, for both the experienced sailor and the novice, all about the sailboat’s different parts. In this article, we learned all about the boat’s hull, the keel, the rudder, the mast, the mainsail, the boom, the kicking strap (boom vang), the topping lift, the jib, the spinnaker, the genoa, the backstay, and the forestay, which make up the basic parts of any sailboat you might find yourself on.
About us
Boatsetter is the go-to app for boat rentals and on-water experiences. Whatever the adventure, we’ve got a boat for that—Set sail , start the party , go yachting , make your trophy catch , and hone your watersports skills! Download the Boatsetter app ( App Store | Google Play ). Make sure to follow @boatsetter on Instagram, and tag us in all your boat day pictures for the chance to be featured.
Rent. List. Share—Only at Boatsetter
Boatsetter empowers people to explore with confidence by showing them a world of possibility on the water. Rent a boat, list your boat, or become a Boatsetter captain today.
Browse by experience
Explore articles
How to Back Up a Boat Trailer in 7 Easy Steps
2022 Port Townsend Wooden Boat Festival: Preview Guide
Boatsetter CMO Pablo Vidal joins team to fill top marketing role
South Florida Tech Startup, Boatsetter, Is Top Finalist At eMerge Americas 2015
9 Popular Boats With Lifting Keels (With Pictures & Prices)
If you are looking for a sailboat, you might want to consider one that features a lifting keel.
Lifting keels allow you to explore shallower waters, reduce drag, or other advantages when the keel is lifted.
Here are the boats you should check out first!
Table of Contents
What is a Lifting Keel?
As you probably know, the keel of a boat is the longitudinal structural device on the bottom of your hull.
On a sailboat, the keel serves as an underwater fluid machine that helps to minimize the lateral motion of the vessel that is under sail, as well as acting as a counterweight to the lateral force that comes from the wind on the sails which can cause it to roll to the side.
A lifting keel, sometimes known as a centerboard, is a keel that retracts into the hull of a sailboat or pivots and allows for certain advantages.
A lifting keel’s main function is to provide a lift to counter the lateral force that is created by the sails. This allows the sailboat to move other directions other than downwind.
Because these keels lift into the hull, you would be able to take your vessel into shallower waters.
In addition, a lifting keel is ideal for:
- Moving the center of resistance.
- Reducing drag.
- Removing the boat from the water and trailering it.
Centerboards are different than other types of keels, such as a ballast keel, because they do not contribute to the overall stability of the vessel because they are not as heavy and instead they only provide lateral resistance.
Great Boats with Lifting Keels Under $30,000
If you are looking for a boat that features a lifting keel and all that comes with it, you are in luck!
Below, I have compiled a list of great boats that feature a lifting keel.
1. Parker 235 Mini Cruiser
The Parker 235 Mini Cruiser is a small sailboat that should be great for sailors who would like to trailer their boat and explore multiple destinations.
This sailboat exhibits excellence both afloat and while onshore. This features high performance due to its long waterline, stable hull, and a deep low center of gravity.
This boat features a custom boat trailer and is easy to launch and as well as to trailer.
This boat is 23’ 5” in length. Despite its smaller size, there is no compromising with the internal accommodations. The boat featured 2 berths, a galley, and a head compartment.
This boat also has a lifting keel which reduces the draft by 3’ 6”.
This boat can be found used at a price of around $20,000.00.
RELATED: Common Problems With Parker Boats .
2. Hunter 22
The Hunter 22 sailboat is a perfect small daysailer that features the capacity to stay aboard overnight. This vessel is ideal for up to five passengers and features a large cabin.
This boat is 21’ 4” in length and is easy to launch, rig, and trailer when needed.
This boat features a lifting keel that reduces draft by 2’ 6” when lifted up.
This boat has a starting price of $29,990.00.
3. BayRaider 20
The BayRaider 20 manufactured by Swallow Yachts, is a small open sailboat that is ideal for families or sailors who are looking for something stable and safe.
This boat has features that make it ideal for beginner sailors including the ability to keep the ballast tanks full for added stability.
This vessel also features a two-masted ketch that gives an advantage over a single-mast rig because it allows for a quick reduction of sail.
This boat is almost 20 feet long and is light enough to be trailered or handled by one person.
This boat features a lifting keel that reduces the draft by 3.8 feet when lifted.
This boat has a starting price of $27,750.00.
4. Catalina 22 Sport
Catalina strives to encourage sailors who are interested in racing with the Catalina 22 Sport. This boat is small and measures at 23’ 10”.
This boat also has a cabin that features berths for up to 4 adults. This boat is a great choice for those looking for speed and easy maneuverability while still offering the ability to stay aboard overnight.
This boat has a lifting keel that reduces the draft of the boat by 3’ 2” while lifted.
This boat has a starting price of $23,550.00.
5. Marlow-Hunter 15
The Marlow-Hunter 15 is a safe and versatile daysailer for families or individuals who new to sailing. This boat was designed with sailing novices in mind and features high sides, a contoured self-bailing cockpit, and a wide beam that was built for comfort.
These safety features will allow peace of mind for parents and brand new sailors.
This vessel is also easy to trailer, rig and launch.
With a length of 14’ 6”, you can fit a crew of up to four onboard but this boat can also be handled solo.
This vessel features a lifting keel that reduces the draft by 3 feet when lifted.
This boat features a highly affordable starting price of $10,123.00.
Models Between $30,000.00 and $100,000.00:
6. feeling 326.
The Feeling 326 was manufactured between the years of 1987 and 1999. This boat is a cruising sailboat that is 32’ 6” in length and comes with 2 cabins, 6 berths, and 1 head.
This boat is great if you plan to go out for long journeys with multiple people.
Even though this boat is an older model, you should still be able to expect quality sailing from them.
This boat also features a lifting centerboard that reduces the draft by 2’ 7”.
Depending on the year and the seller of the vessel, these boats are selling for an average price of between $30,000 and $45,000.00.
7. Norseboat 21.5
The Norseboat 21.5 is the largest model in the Norseboat line with a length of 21’ 10”. You can get either a Cabin or an Open model for this boat.
You can customize this vessel based on your needs and other factors. You can construct a standard or semi-custom Norseboat.
This boat features a lifting centerboard that reduces draft by 2’ 4” when lifted.
Depending on the layout and chosen options, this boat has a starting price of $37,490.00.
Boats Over $100,000.00:
8. alubat ovni 365:.
From the manufacturer Alubat, the Ovni 365 combines their experience in centerboards and high performance to create a vessel that is both comfortable and high performing.
This boat is great whether you are traveling upwind or downwind. This boat is great for both long trips or for simply cruising up and down the coast.
This boat is 39.17 feet long and features a galley as well as a front and rear cabin.
This boat features a lifting centerboard that reduces the draft by about 5.18 feet when lifted.
Depending on the year and specifications of this vessel, the price could range from $100,000 to $300,000.
9. Southerly 42 RST
Southerly makes a mono-hull 42 RST that is an offshore deck saloon sailboat that was built for cruising. This boat has a length of 42’ 2” and could be equipped with either 2-3 cabins, 4-8 berths, and comes with 2 heads.
This boat is great for taking multiple people out on the water. While these are no longer in production, they were made between the years 2007 and 2017.
This boat has a lifting keel that reduces the draft by 6’ 1” when the keel is up.
Depending on the year and the condition, this boat could cost a minimum of $250,000 but if often over $300,000.00.
10. Gunfleet 43
The Gunfleet 43 is a top of the line vessel with many options for customization. This boat is large and luxurious with a length of 44’ 1”.
This boat features a standard layout with either 2 or 3 cabins, or you could get a custom-built version that also has 3 cabins.
This vessel offers high-end luxurious features that are ideal for long trips and even vessels that you would consider for living aboard.
This line features an optional lifting keel that would reduce draft by 4’ 4” when lifted.
This luxurious and custom-crafted vessel has a large price tag of over $800,000.00.
17 Sailboat Types Explained: How To Recognize Them
Ever wondered what type of sailboat you're looking at? Identifying sailboats isn't hard, you just have to know what to look for. In this article, I'll help you.
Every time I'm around a large number of sailboats, I look around in awe (especially with the bigger ones). I recognize some, but with most of them, I'll have to ask the owner. When they answer, I try to hide my ignorance. The words don't make any sense!
So here's a complete list with pictures of the most common sailboat types today. For each of them, I'll explain exactly where the name comes from, and how you can recognize it easily.
So here's my list of popular sailboat types, explained:
Bermuda sloop, sailing hydrofoil, dutch barge, chinese junk, square-rigged tall ship, in conclusion, how to recognize any sailboat.
Before we get started, I wanted to quickly explain what you should look for when you try to identify a sailboat.
The type of sailboat is always determined by one of these four things:
- The type of hull
- The type of keel
- The number of masts
- And the type of sails and rig
The hull is the boat's body. There are basically three hull types: monohull, catamaran, and trimaran. Simply said: do I see one hull, two hulls (catamaran) or three hulls (trimaran)? Most sailboats are monohulls.
Next, there is the keel type. The keel is the underwater part of the hull. Mostly, you won't be able to see that, because it's underwater. So we'll leave that for now.
The sail plan
The last factor is the number of masts and the sail plan. The sail plan, simply put, is the number of sails, the type of sails, and how the sails are mounted to the masts (also called rigging ).
Sailboat are mostly named after the sail plan, but occasionally, a sail type is thrown in there as well.
So now we know what to pay attention to, let's go and check out some sailboats!
Dinghies are the smallest and most simple sailboats around.
They are your typical training sailboats. Small boats with an open hull, with just one mast and one sail. Perfect for learning the ways of the wind.
On average, they are between 6 and 20 ft long. Mostly sailed single-handed (solo). There's no special rigging, just the mainsail. The mainsail is commonly a Bermuda (triangular) mainsail. Dinghies have a simple rudder stick and no special equipment or rigging.
Dinghies are great for learning how to sail. The smaller the boat, the better you feel the impact of your trim and actions.
How to recognize a sailing dinghy:
- short (8ft)
- one Bermuda sail
- open hull design
- rudder stick
Common places to spot them: lakes, near docks
If you'd ask a kid to draw a sailboat, she'll most probably draw this one. The Bermuda Sloop is the most popular and most common sailboat type today. You'll definitely recognize this one.
How to recognize a Bermuda Sloop:
- triangular mainsail (called a Bermuda sail)
- a foresail (also called the jib)
- fore-and-aft rigged
- medium-sized (12 - 50 ft)
Fore-and-aft rigged just means "from front to back". This type of rigging helps to sail upwind.
Any sailboat with one mast and two sails could still be a sloop. Even if the sails are another shape or rigged in another way. For example, here's a gaff-rigged sloop (more on the gaff rig later):
If you want to learn all about sail rigs, check out my full Guide to Understanding Sail Rig Types here. It has good infographics and explains it in more detail
The Bermuda sloop has a lot of advantages over other sailboat types (which is why it's so popular):
- the Bermuda rig is very maneuverable and pretty fast in almost all conditions
- it's really versatile
- you can sail it by yourself without any problems
- it's a simple setup
Common places to spot a sloop: everywhere. Smaller sloops are more common for inland waters, rivers, and lakes. Medium-sized and large sloops are very popular cruising boats.
Cutters have one mast but three or more sails. Most cutters are Bermuda rigged, which means they look a lot like sloops.
How to recognize a cutter:
- looks like a sloop
- two or more headsails instead of one
- commonly one mast
- sometimes an extra mast with mainsail
Cutters have more sail area, which makes them faster, but also harder to sail single-handed. There's also more strain on the mast and rigging.
Common places to spot a cutter: everywhere. Cutters are very popular for cruising.
They mostly have a Bermuda rig, which means triangular sails. But there are also gaff cutters and naval cutters, and some have two masts.
Here's an example of a two-masted naval cutter with an extra gaff mainsail and top gaff:
The Hydrofoil is a pretty new sailboat design. It's a racing sailboat with thin wing foils under the hull. These lift up the hull, out of the water, reducing the displacement to nearly zero. The foils create downforce and keep it from lifting off entirely.
This makes the hydrofoil extremely fast and also impressive.
The hydrofoil refers to the keel type. There are both monohull and multihull hydrofoils.
How to recognize a hydrofoil:
- it flies above the waterline and has small fins
Common places to spot a hydrofoil: at racing events
Famous catamaran: La Vagabonde from Sailing La Vagabonde
A catamaran is a type of cruising and racing multihull sailboat with two hulls. The hulls are always the same size.
Most catamarans have a standard Bermuda rig. The catamaran refers to the hull, so it can have any number of masts, sails, sail types and rig type.
How to recognize a catamaran:
- any boat with two hulls is called a catamaran
Common places to spot catamarans: coastal waters, The Caribbean, shallow reefs
The advantages of a catamaran: Catamarans heel less than monohulls and are more buoyant. Because of the double hull, they don't need as deep a keel to be stable. They have a smaller displacement, making them faster. They also have a very shallow draft. That's why catamarans are so popular in the Caribbean, where there's lots of shallow water.
Catamarans are nearly impossible to capsize:
"Compared with a monohull, a cruising catamaran sailboat has a high initial resistance to heeling and capsize—a fifty-footer requires four times the force to initiate a capsize than an equivalent monohull." Source: Wikipedia
How to recognize a trimaran:
- any boat with three hulls is called a trimaran
Trimarans have three hulls, so it's a multi-hull design. It's mostly a regular monohull with two smaller hulls or floaters on the sides. Some trimarans can be trailered by winching in the auxiliary hulls, like this:
This makes them very suitable for long-term cruising, but also for regular docking. This is great for crowded areas and small berths, like in the Mediterranean. It sure is more cost-effective than the catamaran (but you also don't have the extra storage and living space!).
Common places to spot Trimarans: mostly popular for long-term cruising, you'll find the trimaran in coastal areas.
Gaffer refers to gaff-rigged, which is the way the sails are rigged. A gaff rig is a rectangular sail with a top pole, or 'spar', which attaches it to the mast. This pole is called the 'gaff'. To hoist the mainsail, you hoist this top spar with a separate halyard. Most gaffers carry additional gaff topsails as well.
Gaff rigs are a bit less versatile than sloops. Because of the gaff, they can have a larger sail area. So they will perform better with downwind points of sail. Upwind, however, they handle less well.
How to recognize a gaffer:
- sail is rectangular
- mainsail has a top pole (or spar)
Since a gaffer refers to the rig type, and not the mast configuration or keel type, all sailboats with this kind of rigging can be called 'gaffers'.
Common places to spot a gaffer: Gaffers are popular inland sailboats. It's a more traditional rig, being used recreationally.
Schooners used to be extremely popular before sloops took over. Schooners are easy to sail but slower than sloops. They handle better than sloops in all comfortable (cruising) points of sail, except for upwind.
How to recognize a schooner:
- mostly two masts
- smaller mast in front
- taller mast in the back
- fore-and-aft rigged sails
- gaff-rigged mainsails (spar on top of the sail)
Common places to spot a schooner: coastal marinas, bays
How to recognize a ketch:
- medium-sized (30 ft and up)
- smaller mast in back
- taller mast in front
- both masts have a mainsail
The ketch refers to the sail plan (mast configuration and type of rig). Ketches actually handle really well. The back mast (mizzenmast) powers the hull, giving the skipper more control. Because of the extra mainsail, the ketch has shorter masts. This means less stress on masts and rigging, and less heel.
Common places to spot a ketch: larger marinas, coastal regions
How to recognize a yawl:
- main mast in front
- much smaller mast in the back
- back mast doesn't carry a mainsail
The aft mast is called a mizzenmast. Most ketches are gaff-rigged, so they have a spar at the top of the sail. They sometimes carry gaff topsails. They are harder to sail than sloops.
The yawl refers to the sail plan (mast configuration and type of rig).
Common places to spot a yawl: they are not as popular as sloops, and most yawls are vintage sailboat models. You'll find most being used as daysailers on lakes and in bays.
Dutch Barges are very traditional cargo ships for inland waters. My hometown is literally littered with a very well-known type of barge, the Skutsje. This is a Frisian design with leeboards.
Skutsjes don't have a keel but use leeboards for stability instead, which are the 'swords' or boards on the side of the hull.
How to recognize a Dutch Barge:
- most barges have one or two masts
- large, wooden masts
- leeboards (wooden wings on the side of the hull)
- mostly gaff-rigged sails (pole on top of the sail, attached to mast)
- a ducktail transom
The clipper is one of the latest sailboat designs before steam-powered vessels took over. The cutter has a large cargo area for transporting cargo. But they also needed to be fast to compete with steam vessels. It's a large, yet surprisingly fast sailboat model, and is known for its good handling.
This made them good for trade, especially transporting valuable goods like tea or spices.
How to recognize a Clipper:
- mostly three masts
- square-rigged sails
- narrow but long, steel hull
Common places to spot a clipper: inland waters, used as houseboats, but coastal waters as well. There are a lot of clippers on the Frisian Lakes and Waddenzee in The Netherlands (where I live).
This particular junk is Satu, from the Chesapeake Bay Area.
The Chinese Junk is an ancient type of sailboat. Junks were used to sail to Indonesia and India from the start of the Middle Ages onward (500 AD). The word junk supposedly comes from the Chinese word 'jung', meaning 'floating house'.
How to recognize a Chinese junk:
- medium-sized (30 - 50 ft)
- large, flat sails with full-length battens
- stern (back of the hull) opens up in a high deck
- mostly two masts (sometimes one)
- with two mainsails, sails are traditionally maroon
- lug-rigged sails
The junk has a large sail area. The full-length battens make sure the sails stay flat. It's one of the flattest sails around, which makes it good for downwind courses. This also comes at a cost: the junk doesn't sail as well upwind.
The cat rig is a sail plan with most commonly just one mast and one sail, the mainsail.
Most sailing dinghies are cats, but there are also larger boats with this type of sail plan. The picture above is a great example.
How to recognize a cat rig:
- smaller boats
- mostly one mast
- one sail per mast
- no standing rigging
Cat-rigged refers to the rigging, not the mast configuration or sail type. So you can have cats with a Bermuda sail (called a Bermuda Cat) or gaff-rigged sail (called a Gaff Cat), and so on. There are also Cat Ketches and Cat Schooners, for example. These have two masts.
The important thing to know is: cats have one sail per mast and no standing rigging .
Most typical place to spot Cats: lakes and inland waters
Famous brig: HMS Beagle (Charles Darwin's ship)
A brig was a very popular type of small warship of the U.S. navy during the 19th century. They were used in the American Revolution and other wars with the United Kingdom. They carry 10-18 guns and are relatively fast and maneuverable. They required less crew than a square-rigged ship.
How to recognize a brig:
- square-rigged foremast
- mainmast square-rigged or square-rigged and gaff-rigged
How to recognize a tall ship:
- three or four masts
- square sails with a pole across the top
- multiple square sails on each mast
- a lot of lines and rigging
Square-rigged ships, or tall ships, are what we think of when we think of pirate ships. Now, most pirate ships weren't actually tall ships, but they come from around the same period. They used to be built from wood, but more modern tall ships are nearly always steel.
Tall ships have three or four masts and square sails which are square-rigged. That means they are attached to the masts with yards.
We have the tall ship races every four years, where dozens of tall ships meet and race just offshore.
Most common place to spot Tall Ships: Museums, special events, open ocean
This is a bonus type since it is not very common anymore. As far as I know, there's only one left.
The Trabaccolo is a small cargo ship used in the Adriatic Sea. It has lug sails. A lug rig is a rectangular sail, but on a long pole or yard that runs fore-and-aft. It was a popular Venetian sailboat used for trade.
The name comes from the Italian word trabacca , which means tent, referring to the sails.
How to recognize a Trabaccolo:
- wide and short hull
- sails look like a tent
Most common place to spot Trabaccolo's: the Marine Museum of Cesenatico has a fully restored Trabaccolo.
So, there you have it. Now you know what to look for, and how to recognize the most common sailboat types easily. Next time you encounter a magnificent sailboat, you'll know what it's called - or where to find out quickly.
I loved this article. I had no idea there were so many kinds of sailboats.
i have a large sailing boat about 28ft. that im having a difficult time identifying. it was my fathers & unfortunately hes passed away now. any helpful information would be appreciated.
Jorge Eusali Castro Archbold
I find a saleboat boat but i can find the módem…os registré out off bru’x, and the saleboat name is TADCOZ, can you tell me who to go about this matter in getting info.thank con voz your time…
Leave a comment
You may also like, guide to understanding sail rig types (with pictures).
There are a lot of different sail rig types and it can be difficult to remember what's what. So I've come up with a system. Let me explain it in this article.
The Ultimate Guide to Sail Types and Rigs (with Pictures)
How Much Sailboats Cost On Average (380+ Prices Compared)
Own your first boat within a year on any budget.
A sailboat doesn't have to be expensive if you know what you're doing. If you want to learn how to make your sailing dream reality within a year, leave your email and I'll send you free updates . I don't like spam - I will only send helpful content.
Ready to Own Your First Boat?
Just tell us the best email address to send your tips to:
COMMENTS
The most common sailboat keel types are full-length keels, fin keels, bulb keels, wing keels, bilge keels, and lifting keels. Full keels are popular among cruisers, while fin keels are generally used for racing. Bilge keels and lifting keels are typically used in tidal waters, on small fishing boats for example.
Browse 295 sailboat keel photos and images available, or start a new search to explore more photos and images. sailing boats or yachts - sailboat keel stock illustrations. Sailing Boats or Yachts. barnacles on the hull and keel of a yacht propped up in dry dock - sailboat keel stock pictures, royalty-free photos & images.
If you want to watch one video on keel types and just get it, this one is for you. Keels don't have to be confusing; simply classify them the right way. I've...
Browse 1,000+ sailboat keel stock photos and images available, or start a new search to explore more stock photos and images. Sort by: Most popular. Sailing Boat bow during cruise Sailing Boat bow during cruise sailboat keel stock pictures, royalty-free photos & images.
A full keel runs from end to end of the boat lengthways. A full keel, as the name implies, runs almost the entire length of the boat. At a minimum, it must run 50% of the length of the boat. A full keel is one of the most stable keel types, which is why it is so common. Full keels are also safer should you run aground.
Search from Sailboat Keel Pictures stock photos, pictures and royalty-free images from iStock. Find high-quality stock photos that you won't find anywhere else.
Find Sailboat keel stock images in HD and millions of other royalty-free stock photos, illustrations and vectors in the Shutterstock collection. Thousands of new, high-quality pictures added every day.
Browse Getty Images' premium collection of high-quality, authentic Sailboat Keel stock photos, royalty-free images, and pictures. Sailboat Keel stock photos are available in a variety of sizes and formats to fit your needs.
Find Sailboat Keel stock photos and editorial news pictures from Getty Images. Select from premium Sailboat Keel of the highest quality.
2,971 sailing boat keel stock photos, 3D objects, vectors, and illustrations are available royalty-free. ... 143 p.m., on the lake a Valk Jolle, a small open sailing boat with gaff sails and a fixed keel. The boat is a gaff-rigged sloop. Vector illustration of four small ships in different colors: a sailboat, a yacht, a fishing boat and a ...
Sailboat keels usually carry iron or lead ballast in their tip to act as a counterweight to the wind's force on the sails, which reduces heeling. The keel's length acts as a lever, increasing the ballast's effectiveness and improving its stabilizing properties. In other words, the deeper the keel runs and the heavier its ballast is, the more ...
Browse 4,594 authentic keel stock photos, high-res images, and pictures, or explore additional boat keel or keel beach stock images to find the right photo at the right size and resolution for your project. Sailing Boats or Yachts. Abstract photo of stacked blue boats upside down. Barnacles on the hull and keel of a yacht propped up in dry dock ...
A wing keel sailboat may also be prone to increased leeway due to the lower depth and surface area of the keel. This can make the boat more difficult to control in strong winds or challenging sea conditions. Another issue to consider is the maintenance and cleaning of the wing keel. Due to the horizontal wings, it may be harder to access and ...
The hull of an old boat is the frame of a wooden boat, a wooden structure consisting of the keel and frames of a half-built boat. Find Boat Keel stock images in HD and millions of other royalty-free stock photos, 3D objects, illustrations and vectors in the Shutterstock collection. Thousands of new, high-quality pictures added every day.
A basic sailboat is composed of at least 12 parts: the hull, the keel, the rudder, the mast, the mainsail, the boom, the kicking strap (boom vang), the topping lift, the jib, the spinnaker, the genoa, the backstay, and the forestay. Read all the way through for the definition of each sailboat part and to know how they work.
sailing boat in race sailing boat Keel stock pictures, royalty-free photos & images. sailing boat in race. sailing boat. Boat maintenance Falsterbo, Sweden - April 11, 2016: Senior adult man standing on a foldable ladder while polishing a sailboat. Real people in everyday life. Keel stock pictures, royalty-free photos & images
Browse 1,900+ ship keel stock photos and images available, or search for yacht or sailboat to find more great stock photos and pictures. underwater shot of a propeller of a motor boat in the sea. Model wooden ship isolated on white background. Looking up at the propeller and keel of a free fall lifeboat, located on a harbour wall for training ...
The winged keel works by using a series of wing-like structures on the bottom of the keel to create lift. As the boat moves through the water, the wings generate lift, which reduces the amount of drag. This allows the boat to move through the water more efficiently, leading to faster speeds and better performance.
This boat has a lifting keel that reduces the draft by 6' 1" when the keel is up. Depending on the year and the condition, this boat could cost a minimum of $250,000 but if often over $300,000.00. 10. Gunfleet 43. The Gunfleet 43 is a top of the line vessel with many options for customization.
Browse 4,600+ keel boat stock photos and images available, or search for keelboat or ship to find more great stock photos and pictures. keelboat. ship. Sort by: Most popular. Bow of large motor yacht at sea. Bow of large luxury motor yacht sailing at sea on tropical ocean.
The 13 most popular swing keel sailboats that you may find worthy to consider are the following: Catalina 22, MacGregor 26, Hunter 22, Precision 23, O'Day 22, Beneteau First 235, Seaward 25, Islander Bahama 24, Watkins 27, Com-Pac 23, Montgomery 17, San Juan 23, and West Wight Potter 19. The estimated pricing for the boats with swing keels ...
This day that began with a beached SUV at Lincoln Park is concluding with a beached sailboat at Alki. Thanks to the reader who sent the photos with a tip about the SFD/SPD response by land and sea ...
one mast. triangular mainsail (called a Bermuda sail) a foresail (also called the jib) fore-and-aft rigged. medium-sized (12 - 50 ft) Fore-and-aft rigged just means "from front to back". This type of rigging helps to sail upwind. Any sailboat with one mast and two sails could still be a sloop.